您好,歡迎光臨萊州全部污视频app网站機械有限公司官方網站! 鄭重聲明 進入官網

攪拌車發動機損壞全程不付费看污软件片需要修補哪些事項?

來源:http://www.nordic-bebee.com/ 日期:2020-11-11 發布人:admin
1、氣門腳空地的調整:配氣安排各機件在正常運用中,跟著零件的磨損,氣門腳空地將發生改動。如凸輪、氣門杆端麵及挺杆接觸麵磨損後空地將變大,而氣門頭與氣門座磨損後空地又變小,因此,在調整中應取空地的基地值為宜。如規矩為0.2~0.25mm,可實取0.22mm,這麽既照顧了空地改動的實際情況,又思考了測量誤差疑問,可充沛保證氣門腳空地效果的完成。
1. Adjustment of valve foot space: valve arrangement in normal operation, with the wear of parts, the valve foot space will change. If the cam, valve rod end face and tappet contact surface wear, the open space will become larger, while the valve head and valve seat wear, the open space will become smaller. Therefore, the base value of open space should be taken in the adjustment. If the rule is 0.2 ~ 0.25 mm, the actual value can be 0.22 mm. This not only takes into account the actual situation of the change of the open space, but also considers the question of the measurement error, which can fully ensure the completion of the air gap effect of the valve foot.
2、氣門座的鉸削:氣門座鉸削通常為手作業業,應格外重視三個疑問:一是在消除凹陷、斑駁,能鉸出無缺錐麵的基礎上,鉸削量越小越好;二是鉸削時用力要均勻,起刀收刀要輕,少鉸多調查,以保證較少的鉸削量和較高的光潔度;三是與氣門試配,判定好作業麵方位和寬度。方位應調整到氣門錐麵的中下部,偏上或偏下可用上、下口鉸刀進行調整。作業麵寬度,進氣門可掌握在0.9mm(規矩為1~2.2mm),排氣門可掌握在1.4mm(規矩為1.5~2.5mm)。實踐證明上述寬度在氣門與氣門座研磨後,進氣門可達1mm,排氣門可達1.5mm,均在規矩寬度的下限,能大大提高其運用壽數。
2. Valve seat reaming: valve seat reaming is usually a manual operation, and three questions should be paid special attention to: first, on the basis of eliminating depression and mottling, and reaming out no missing cone surface, the smaller the reaming amount is, the better; second, the force should be even when reaming, and the knife should be lifted and closed lightly, and more investigation should be carried out to ensure less reaming amount and higher smoothness; The third is to match with the valve to determine the working face orientation and width. The orientation should be adjusted to the middle and lower part of the valve cone surface, and the upper and lower reamers can be used to adjust the position. The width of working face can be controlled within 0.9mm for inlet valve and 1.4mm for exhaust valve (1.5-2.5mm). Practice has proved that after grinding the valve and valve seat, the inlet valve can reach 1 mm and the exhaust valve can reach 1.5 mm, which are both within the lower limit of the regular width, which can greatly improve the service life of the valve.
中科攪拌機
3、攪拌車修補質量差在修補作業中出色的疑問是氣門與氣門座作業麵加工質量達不到懇求,構成作業麵燒蝕、凹陷而前期損壞;凸輪軸軸承在刮削中其協作空地、接觸麵積、各軸承同心度達不到懇求,加速磨損,呈現異響構成前期損壞;氣門導管在更換新件時,鉸削質量達不到規矩懇求,直接影響氣門及氣門座運用壽數。
3. The repair quality of mixer truck is poor. In the repair operation, the outstanding question is that the processing quality of valve and valve seat working surface can not meet the requirements, which constitutes ablation and depression of working surface, and early damage; camshaft bearing in scraping, its cooperation space, contact area, bearing concentricity can not meet the requirements, accelerate wear and appear abnormal noise, which constitutes early damage; when valve guide is replaced with new parts, hinge Cutting quality can not meet the requirements, which directly affects the service life of valve and valve seat.
4、凸輪軸軸承的刮削:凸輪軸軸承的刮削歸於手作業業,保證質量有一定難度。為刮削便利,又通常在氣缸體外加工,因此應格外留意四個疑問:一是要判定好軸承刮削後內孔的直徑;二是刮削中要盡量留意堅持軸承內孔與外圓的同軸度;三是邊刮削邊與軸頸試配,並保證接觸印痕分布均勻;四是將軸承壓入座孔時,應留意對正油孔。刮削後裝入凸輪軸,翻滾數圈,視情進行恰當修整,接觸麵積應抵達75%以上並分布均勻,空地符合規矩。
4. Scraping of camshaft bearing: scraping of camshaft bearing belongs to manual operation, so it is difficult to ensure quality. For the convenience of scraping, it is usually processed outside the cylinder. Therefore, we should pay special attention to the following four questions: first, determine the diameter of the inner hole of the bearing after scraping; second, pay attention to the coaxiality between the inner hole and the outer circle of the bearing; third, try to fit the bearing with the journal while scraping, and ensure that the contact marks are evenly distributed; fourth, when pressing the bearing into the seat hole, pay attention to aligning the oil hole. After scraping, install the camshaft, roll it for several turns, and properly trim it according to the situation. The contact area should reach more than 75% and be evenly distributed. The open space should meet the regulations.

上一篇:移動式混凝土攪拌車離不開哪些結構?
下一篇:趣影阁自上料混凝土攪拌車生產技術